Noise Control Management

Noise Control Management 

Yogya / Bali/ Balikpapan/ Solo /Lombok/ Bandung | 2 – 4 april 2013 | Fee : bergantung Venue
Yogya / Bali/ Balikpapan/ Solo /Lombok/ Bandung | 16 – 18 april 2013 | Fee : bergantung Venue
Yogya / Bali/ Balikpapan/ Solo /Lombok/ Bandung | 30 april – 2 mei 2013 | Fee : bergantung Venue
Yogya / Bali/ Balikpapan/ Solo /Lombok/ Bandung | 14 – 16 mei 2013 | Fee : bergantung Venue
Yogya / Bali/ Balikpapan/ Solo /Lombok/ Bandung | 28 – 30 mei 2013 | Fee : bergantung Venue
Yogya / Bali/ Balikpapan/ Solo /Lombok/ Bandung | 4 – 6 juni 2013 | Fee : bergantung Venue
Yogya / Bali/ Balikpapan/ Solo /Lombok/ Bandung | 18 – 20 juni 2013 | Fee : bergantung Venue

Jadwal Training 2013 Selanjutnya …

Description

One possible cause of hearing damages on men is the level of noise exposures that beyond the limit of sound pressure level or percent dose allowed for a normal working hours. Industrial workers, who receive noise exposure in their everyday working environment, are vulnerable to experience hearing damage either in the form of temporary (TTS) or permanent threshold shift ((PTS). Therefore, the industry should establish a professional program of noise control management in order to protect the health and safety of the workers.
In association with Indonesian regulation for safety and healthy working condition (PP No. 3 1975), limit of Leq 85 dBA noise exposure level for 8 hours working day is required for work places. Instead, a Leq limit of 90 dBA steady noise levels for 8 hours working day is determined in OSHA regulation (1974) for occupational noise. Higher levels of noise will reduce the allowable exposure time or working period of workers; therefore, a feasible administrative or engineering noise controls should be applied. When employees are subjected to noise exposures exceeding the limit stated in OSHA regulation, personal ear protectors, such as, earplug or earmuff, shall be provided.

The objectives of this training are:

1. Learn about noise in industry and the effects of noise to workers
   Learn about noise measurement and analysis techniques including instrumentation
2. Learn how to design, monitor and implementing a management system for preserving health and safety of workers from noise exposure in industry
3. Learn how to design, monitor and implementing noise control engineering in industry

Materi

• INTRODUCTION
• FUNDAMENTALS OF ACOUSTICS
  1. Sound Levels and Decibel Scales
  2. Sound Propagation Outdoors and Indoors
  3. Air and Structure borne Sound Propagations
• NOISE SOURCES IN INDUSTRY
  1. Fan Noise
  2. Compressor and Pump Noise
  3. Jet Noise
  4. Pipe Flow Noise
  5. Other Noise Sources
• NOISE MEASUREMENT AND FREQUENCY ANALYSIS
  1. Measurement Methods
  2. Microphones
  3. SLM and Integrating Devices
  4. Time Varying Noise and Spectrum Analysis
  5. Audiometer
• HEARING CHARACTERISTICS
  1. Hearing Mechanism and Threshold of Hearing
  2. Loudness Levels and Computation
  3. Hearing Loss and Audiometric Test
• EFFECTS OF NOISE ON HUMAN
  1. Annoyance Levels
  2. Noise Induced Hearing Loss
  3. Noise Dose Calculation
• NOISE CONTROL TECHNIQUES
  1. Planning a Noise Control Program
  2. Noise Control by Planning and Maintenance
  3. Enclosure and Barriers
  4. Silencers, Mufflers and Attenuators
  5. Noise Control by Room Treatment
• NOISE CONTROL MANAGEMENT
  1. Priority Planning and Approach
  2. Noise survey and Visual Inspection
  3. Noise Abatement Procedures and Guidelines
  4. Hearing Conservation Program
  5. Noise Control Standards and Regulations

• TUTORIALS AND PRACTICAL WORKS

1. Insulation
2. Noise measurement and frequency analysis
3. Noise Dose

Peserta

Pelatihan Ini Sangat Penting Bagi :

The following selected participants should attend this course:

• Electric Engineer/ Supervisor/ Technician
• Plant Maintenance Engineer/ Supervisor/ Superintendent
• Engineer from transformer manufacture
• Staffs who are in charge of ordering, replacement and
• Refurbishing of electrical equipment
• Experience professional who want to review or broaden their understanding of transformer system
• Everybody or professional who wants to broaden knowledge or gain benefit from this course

Metode

Presentasi, Diskusi, Simulasi, Studi kasus, Evaluasi

Instructor

Iswantoro, MSi (CV terlampir)

Duration:

3 days training

Time & Venue :

Jadwal 2013

• 8 – 10 Januari 2013
• 22 – 24 januari 2013
• 5 – 7 februari 2013
• 19 – 21 februari 2013
• 5 – 7 maret 2013
• 2 – 4 april 2013
• 16 – 18 april 2013
• 30 april – 2 mei 2013
• 14 – 16 mei 2013
• 28 – 30 mei 2013
• 4 – 6 juni 2013
• 18 – 20 juni 2013
• 25 – 27 juni 2013
• 9 – 11 juli 2013
•  23 – 25 juli 2013
• 6 – 8 agustus 2013
• 13 – 15 agustus 2013
•  27 – 29 agustus 2013
•  3 – 5 september 2013
• 17 – 19 september 2013
• September 24th – 26th 2013
• 8 – 10 Oktober 2013
• 15 – 17 Oktober 2013
• 29 – 31 Oktober 2013
• 12 – 14 November 2013
• 26 – 28 November 2013
• 3 – 5 desember 2013
• 10 – 12 desember 2013
• 24 – 26 desember 2012

Fasilitas:

• Training kit
• Hard and soft copy materi (flashdisk)
• Sertifikat
• Souvenir
• 2x coffee break and lunch
• Transportasi antar jemput selama training ( bandara / stasiun/ terminal -hotel-tempat pelatihan PP)

cforms contact form by delicious:days